Hear from Our Customers
You’re running the AC, someone turns on the microwave, and the breaker trips again. That’s not just annoying—it’s your electrical panel telling you it can’t handle what your home demands anymore.
Most homes in Denton built before 2000 have 100-amp panels. Your modern appliances, HVAC system, and electronics need closer to 200 amps. When you upgrade, breakers stop tripping, lights stop dimming, and you stop worrying whether your electrical system is safe.
After a proper home electrical repair and installation, your panel distributes power evenly across circuits. No more choosing between the dryer and the air conditioner. No more flickering lights when the fridge kicks on. Just steady, reliable power that handles everything you plug in without hesitation.
We’ve spent over 25 years working on homes across Denton County. We’re not new to this area, and we’re not learning on your property.
Every electrician on our team carries full Texas licensing and insurance. That A+ Better Business Bureau rating didn’t come from cutting corners—it came from showing up when we say we will and doing the work right. Our Super Service Awards from Angie’s List reflect what matters most: homeowners trust us to handle their electrical systems safely.
Denton’s summer heat pushes electrical systems hard. When your AC runs nonstop and your panel can’t keep up, you need someone who understands how North Texas weather affects older homes. We’ve upgraded hundreds of panels in this area, and we know exactly what your home needs to stay powered through August and February alike.
First, we come to your home and look at your current electrical setup. We check your panel, measure your load, inspect your wiring, and figure out what’s causing the problem. You get a clear explanation of what’s wrong and what it’ll cost to fix—before any work starts.
If you’re upgrading your panel, we pull the permits and coordinate with the city. We install the new 200-amp panel using NEMA-rated components and UL-listed materials that meet current NEC codes. Your power stays off for about four to six hours during installation, and we schedule around your day to minimize disruption.
After installation, we test every circuit, verify proper grounding, and make sure everything works exactly as it should. Then the city inspector comes out, checks our work, and signs off. You get documentation showing your electrical system is code-compliant and safe—which matters when you sell your home or file an insurance claim.
Ready to get started?
When we handle electrical troubleshooting for homes in Denton, TX, we’re looking at the whole system—not just the obvious problem. A flickering light might be a loose bulb, or it might be a voltage drop from an overloaded circuit two rooms away. We trace the issue back to its source.
Panel upgrades include the new breaker box, all necessary wiring updates, proper grounding, weatherhead replacement if needed, and coordination with Oncor for temporary disconnect. We use commercial-grade materials that last decades longer than standard residential components. Every connection gets torqued to spec, every wire gets labeled, and every circuit gets tested under load.
Denton homes built in the 1970s and 1980s often have aluminum wiring, which expands and contracts differently than copper. If your outlets feel warm or you smell something burning near switches, that’s aluminum wiring loosening at connection points. We retrofit those connections with approved methods that prevent overheating and eliminate fire risk. It’s not always a full rewire—sometimes it’s targeted fixes that make your existing wiring safe again.
Your breakers trip frequently even when you’re not running anything unusual. Lights dim when the AC kicks on. You can’t run the microwave and toaster at the same time without losing power to the kitchen.
Those are signs your panel can’t deliver enough amperage for your home’s current demand. Most older Denton homes have 100-amp service, which was fine in 1985 but struggles with modern loads. If you’ve added central air, a hot tub, an electric vehicle charger, or multiple computers and TVs, your electrical system is working harder than it was designed to handle.
Another clear sign: your panel has a Federal Pacific or Zinsco label. Both brands have documented safety issues and should be replaced regardless of capacity. If you’re planning a kitchen remodel or adding square footage, building codes will likely require a panel upgrade before permits get approved.
North Texas storms create voltage fluctuations in the power grid. When wind knocks tree branches into lines or lightning strikes nearby transformers, Oncor’s system tries to reroute power automatically. That causes brief dips and surges that make your lights flicker.
If flickering only happens during storms and stops afterward, it’s usually grid-related and not something you can fix. But if lights flicker when you turn on appliances or continue flickering after storms pass, that’s a problem inside your home. Loose connections at the panel, corroded wiring, or an undersized service line can all cause persistent flickering.
Whole-house surge protection helps during storms by absorbing voltage spikes before they reach your electronics. It won’t stop flickering, but it will prevent expensive damage to computers, TVs, and appliances. We install surge protection at the panel level, which protects everything in your home instead of just what’s plugged into individual surge strips.
Plan on four to six hours without power on installation day. We coordinate with Oncor to disconnect your service, install the new panel and components, reconnect everything, and test all circuits before restoring power.
The timeline starts before installation day. We pull permits from the city, which takes a few days. We order your specific panel and materials, which usually arrive within a week. Then we schedule the work around your availability and Oncor’s disconnect schedule.
After installation, a city inspector comes out to verify everything meets code. That inspection usually happens within two to three business days. Total timeline from your approval to final inspection: about two weeks. The actual work happens in one day, but the permitting and inspection process takes longer. We handle all coordination with the city and utility company so you don’t have to track down inspectors or wait on hold with Oncor.
Absolutely. Not every electrical issue requires a panel upgrade. Sometimes a single circuit is overloaded and needs to be split. Sometimes a breaker has worn out and needs replacement. Sometimes outdoor outlets have lost their GFCI protection and need new devices.
We start every service call with electrical troubleshooting to find the actual problem. If your kitchen outlets stopped working, we check the GFCI outlet first, then the breaker, then the wiring between the panel and the outlets. Most of the time, it’s something simple that takes an hour to fix.
But if we find multiple issues—corroded connections, outdated wiring methods, a panel that’s rusted inside, or breakers that keep failing—then we’ll recommend a larger fix. We’re not going to sell you a panel upgrade if resetting a GFCI solves your problem. You’ll get an honest assessment of what needs fixing now and what can wait.
Yes. We install standby generators that turn on automatically when grid power fails. These aren’t portable generators you wheel out of the garage—they’re permanent units that sit outside your home and connect directly to your electrical panel.
The process starts with a site evaluation. We figure out where the generator goes, how far it sits from your home, and whether you need a concrete pad. We run a gas line from your meter to the generator location, install an automatic transfer switch inside your panel, and connect everything according to manufacturer specs and local codes.
When Oncor’s power goes out, the transfer switch detects the outage within seconds and signals the generator to start. Your home switches to generator power in less than a minute. When grid power returns, the system switches back automatically and the generator shuts down. You don’t flip any switches or go outside in the storm—it all happens on its own while you stay comfortable inside.
Turn off the breaker that controls that outlet or switch immediately. Don’t use that circuit until an electrician inspects it. Burning smells mean something is overheating, and overheating causes fires.
Common causes: loose wire connections, damaged insulation, or an outlet handling more load than it’s rated for. Sometimes it’s a failing device—the outlet or switch itself has worn out. Sometimes it’s a bigger problem like aluminum wiring expanding and contracting at connection points until the connection loosens and arcs.
Call us right away if you smell burning. This isn’t something to monitor or wait on. We’ll come out, identify where the heat is coming from, and fix it before it becomes a fire hazard. Most burning smell calls are urgent enough that we prioritize them the same day. Your home’s safety isn’t worth gambling on, and electrical fires move fast once they start.
