Hear from Our Customers
If your kitchen appliances can’t run at the same time without tripping a breaker, you’re not asking too much of your home. Your electrical panel is just undersized for how you actually live now.
Most homes built in North Richland Hills during the 80s and 90s came with 100 or 150-amp panels. Back then, that was plenty. Now you’ve got computers, tablets, charging stations, smart home devices, and a garage full of power tools. Your system wasn’t designed for that load.
A proper electrical panel upgrade in North Richland Hills brings your home up to 200 amps. That means running your microwave and coffee maker at the same time without killing power to half the kitchen. It means charging your car overnight without worrying about overloading circuits. It means your home keeps up with your life instead of fighting it.
We’ve been handling electrical services in North Richland Hills and the Mid-Cities for over 25 years. We’re family-owned, fully licensed through the Texas Department of Licensing and Regulation, and we carry an A+ rating with the Better Business Bureau.
We’re not the cheapest option in town, and we won’t pretend to be. You’re paying for commercial-grade components that last decades, not the builder-grade stuff that fails in five years. You’re paying for electricians who know Fort Worth’s code requirements inside out and handle permits correctly the first time.
North Richland Hills has over 70,000 residents, and a lot of those homes were built during the same era with the same electrical setups. We’ve upgraded hundreds of panels in this area. We know what your inspector will flag before they even show up.
First, we come out and look at your current setup. We check your panel, measure your load, and figure out what size upgrade you actually need. Not every home needs 200 amps, but most in North Richland Hills do if you’re planning to stay long-term.
Once we know what you need, we pull the permit through the city. Fort Worth and the Mid-Cities have specific code requirements, and we handle that paperwork. Then we schedule the install around your availability—usually takes a day, sometimes less depending on the scope.
During installation, your power will be off for a few hours while we swap the panel and reconnect everything to code. We install the new breaker box, run any additional circuits you need, and make sure everything’s grounded and protected properly. After that, the city inspector comes out to sign off. We don’t leave until it passes.
You’ll also get GFCI protection added in kitchens, bathrooms, and garages if your home was built before 1987. That’s required now, and it’s a real safety upgrade—not just a code checkbox.
Ready to get started?
A panel upgrade isn’t just swapping out the box on your wall. It’s a full electrical maintenance check that brings your home up to current safety standards.
We install whole-home surge protection during most upgrades. Texas storms are brutal on electronics, and a single lightning strike can fry everything plugged into your walls. Surge protection at the panel level stops that before it reaches your devices.
If you’re adding an electric vehicle charger or a backup generator, we handle that wiring installation at the same time. It’s easier to do it all at once than to open the panel again six months later. Same goes for additional circuits—if you’re finishing a garage, adding a home office, or upgrading your HVAC, we run those lines while the panel’s already open.
North Richland Hills homes built in the 80s often have aluminum wiring in some circuits. If we spot that during the inspection, we’ll flag it. Aluminum wiring isn’t automatically dangerous, but it does need specific handling. We’ll walk you through what needs attention and what can wait.
Most residential panel upgrades in North Richland Hills run between $2,500 and $4,500 depending on the size of the upgrade and how much additional work is involved. A straightforward swap from 100 amps to 200 amps with no extra circuits usually lands on the lower end. If you’re adding circuits, upgrading the meter base, or running new wiring for specific appliances, that pushes the price higher.
The permit and inspection fees are separate and run a few hundred dollars through the city. We handle that process, but it’s a line item you’ll see on the estimate. If your home needs a service line upgrade from the street, that’s additional and involves coordinating with the utility company. Most homes don’t need that, but older properties sometimes do.
We give you a detailed written estimate before any work starts. No surprises, no “we found something else” upsells halfway through the job. You’ll know exactly what you’re paying for and why.
The actual installation usually takes four to eight hours depending on the complexity of your setup. Simpler jobs where we’re just swapping the panel and reconnecting existing circuits can be done in half a day. More involved projects—like adding circuits, relocating the panel, or upgrading the meter base—can stretch into a full day or slightly more.
Your power will be off during part of that time, usually three to five hours while we disconnect the old panel and wire in the new one. We try to schedule that window during the cooler parts of the day if it’s summer, but North Richland Hills heat doesn’t always cooperate. Plan to be without AC, refrigeration, and electronics during that stretch.
After installation, the city inspector needs to come out and approve the work. That usually happens within a day or two of us finishing. Once it passes inspection, you’re good to go. If you need the work done faster for any reason, we offer same-day emergency electrical services for urgent situations, though panel upgrades typically aren’t emergencies unless there’s a serious safety issue.
If your breakers trip regularly, your panel feels warm to the touch, or you’re adding major appliances like an EV charger or backup generator, yes—you need an upgrade. Those aren’t minor inconveniences. They’re signs your system is overloaded and potentially dangerous.
Homes in North Richland Hills built before 2000 often have 100 or 150-amp panels. That was fine when homes had one TV, a single desktop computer, and basic kitchen appliances. Now you’re running multiple laptops, phone chargers, smart home systems, garage door openers, and high-efficiency HVAC systems. The load is completely different.
An undersized panel doesn’t just trip breakers. It creates heat, which degrades wiring insulation over time and increases fire risk. If you’re planning to sell in the next few years, an outdated panel will show up on the buyer’s inspection and become a negotiating point. Upgrading it now means you’re not dealing with that later. It also means your homeowner’s insurance is less likely to flag your electrical system during a policy review.
Not directly. A panel upgrade doesn’t reduce how much electricity your appliances use—it just makes sure your system can handle the load safely. Your bill is based on consumption, and swapping the panel doesn’t change that.
That said, if you’re upgrading your panel as part of a larger home rewiring project or adding energy-efficient systems, you might see savings from those changes. For example, if you’re installing LED lighting, a smart thermostat, or a more efficient HVAC system at the same time, those upgrades can reduce your monthly usage. The average electric bill in North Richland Hills is around $186 per month, and small efficiency improvements can shave 10-15% off that over time.
The real value of a panel upgrade isn’t in your monthly bill—it’s in safety, reliability, and the ability to use your home the way you need to without constantly resetting breakers or worrying about electrical fires. If your current system is struggling, you’re already paying for it in damaged electronics, service calls, and stress. Fixing it once eliminates all of that.
Legally, no. Texas requires all electrical panel work to be done by a licensed electrician and inspected by the city. There’s no homeowner exemption for this type of work. Even if you have electrical experience, you can’t pull the permit yourself, and you can’t pass inspection without a licensed contractor’s signature.
Beyond the legal side, panel work is legitimately dangerous. You’re working with live 240-volt service coming from the utility. One wrong move and you’re dealing with arc flash, serious burns, or worse. It’s not like changing a light fixture. The main breaker doesn’t shut off the power coming into the panel—only the utility can do that, and they won’t do it for a DIY project.
Insurance is another issue. If something goes wrong with a DIY panel install—fire, injury, property damage—your homeowner’s policy won’t cover it. They’ll deny the claim the second they find out unlicensed work caused the problem. We carry insurance specifically for this work. If something goes wrong, you’re covered. If you do it yourself, you’re on your own.
The main difference is the type of systems they work on and the code requirements they follow. A commercial electrician in North Richland Hills handles three-phase power, larger electrical loads, and more complex wiring setups for businesses and industrial properties. A residential electrician focuses on single-phase systems, home wiring, and the specific code requirements for houses.
That said, a lot of electrical contractors do both. We handle both residential and commercial electrical work, which means we’re used to working with commercial-grade components and higher standards. When we install a residential panel, we’re using the same quality parts and installation methods we’d use on a commercial job. That’s why our work lasts longer than the standard residential-grade installs most companies do.
If you’re a homeowner, you want someone who regularly works on homes and knows the local residential code inside out. If you’re a business owner, you want someone who understands commercial electrical requirements and can handle the permitting process for larger projects. Either way, make sure whoever you hire is fully licensed through the Texas Department of Licensing and Regulation and carries current insurance. That’s non-negotiable.
