Hear from Our Customers
You flip a switch and the lights come on. Your AC runs all summer without tripping breakers. Your panel can handle your EV charger, your smart home setup, and everything else you plug in without overloading.
That’s what happens when your electrical system is actually built to handle what you’re asking it to do. Most homes in Grapevine—especially anything built before 2000—are running on 100-amp panels that were never designed for modern electrical loads. Add in a couple of window units, a Tesla charger, and all the devices your family uses daily, and you’re pushing that system past its limit.
We size panels correctly. We use commercial-grade components that last decades, not years. And we don’t cut corners on wire gauge, breaker quality, or grounding—because that’s where most electrical problems start. You get a system that handles your actual life, not just what passed code twenty years ago.
We’ve been handling electrical work across the Dallas-Fort Worth area since before Grapevine Mills became the shopping destination it is today. We’ve wired new construction near the Gaylord Texan, upgraded panels in historic downtown homes, and kept the lights on for businesses along Main Street.
We’re licensed, insured, and we hold an A+ rating with the Better Business Bureau. Our work has earned multiple Super Service Awards from Angie’s List because we show up when we say we will, we quote the job honestly, and we don’t leave until it’s done right. You’re not getting a national franchise or a contractor who’s learning on your dime—you’re getting electricians who’ve spent decades working in North Texas and know exactly what this climate and this building stock requires.
You call or submit a request online. We schedule a time that works for you—not a four-hour window where you’re stuck waiting. Our electrician shows up on time, walks through what you’re dealing with, and gives you a clear assessment of what needs to happen.
Before any work starts, you get an upfront price. No surprises, no “we found something else” upsells unless there’s an actual safety issue we can show you. If your panel needs upgrading, we explain why. If your wiring is outdated or dangerous, we show you what we’re seeing. You decide what happens next.
Once you approve the work, we get it done. We pull permits when required, we install everything to current code, and we clean up when we’re finished. You get a warranty on the installation—two to five years depending on the scope—and you have our number if anything comes up later. That’s it. No drama, no runaround.
Ready to get started?
We handle panel upgrades, which is the most common job we do in Grapevine. If your home still has a Federal Pacific, Zinsco, or Challenger panel, most insurance companies won’t cover you until it’s replaced—and for good reason. Those panels are fire hazards. We swap them out for modern, code-compliant panels sized to handle your actual electrical load.
We also install whole-house surge protection, which matters more than most people realize. Texas had 210 power outages between 2000 and 2023—more than any other state. Every time the grid flickers or a storm rolls through, your electronics are at risk. Whole-house surge protection stops that damage before it reaches your devices.
Generator installations are another big part of what we do. After the 2021 freeze, a lot of Grapevine residents decided they weren’t going through that again. We install Generac and Kohler standby generators that kick on automatically when the power drops. You stay comfortable, your food stays cold, and your family stays safe—no matter what ERCOT is dealing with. We also wire EV charging stations, install recessed lighting, rewire older homes, and handle any electrical repair that comes up. If it’s powered by electricity, we can fix it or install it.
Your breakers trip frequently, especially when you’re running the AC and other appliances at the same time. That’s the most common sign. Your panel is doing its job—it’s shutting off power before the wiring overheats—but it’s also telling you that your system can’t handle what you’re asking it to do.
Other signs include flickering lights, outlets that feel warm to the touch, or a panel that’s more than 25 years old. If you’re planning to install an EV charger, add a home office, or upgrade your HVAC system, your current panel probably won’t support it. Most homes in Grapevine built before 2000 have 100-amp panels, and modern homes need at least 200 amps to run comfortably.
If your panel is a Federal Pacific, Zinsco, or Challenger brand, it needs to be replaced immediately. Those panels are known fire hazards, and many insurance companies won’t cover homes that still have them installed. We can assess your panel during a service call and let you know exactly what you’re working with.
We start by sizing the new panel based on your home’s actual electrical load—not just what’s there now, but what you’ll need in the next ten years. If you’re planning to add an EV charger or a backup generator, we factor that in. Most upgrades go from 100 amps to 200 amps, but some homes need more depending on square footage and equipment.
The work itself takes about a day for a standard residential panel. We coordinate with Oncor to disconnect power temporarily, we remove the old panel, install the new one, and reconnect all your circuits. We pull the necessary permits through the city of Grapevine and schedule the inspection. Once it passes, you’re done.
You’ll notice the difference immediately. Your breakers stop tripping. Your lights stop dimming when the AC kicks on. And you’ll have the capacity to add whatever electrical upgrades your home needs without worrying about overloading the system. We warranty the installation for five years, and the panel itself is built to last 30-plus years.
Yes, especially in North Texas. We get more lightning storms, grid fluctuations, and power outages than most of the country. Every time the power blinks or surges, it sends a spike through your wiring that can fry electronics, damage appliances, and shorten the lifespan of anything plugged into your walls.
Whole-house surge protection installs directly at your panel and stops those surges before they reach your outlets. It’s different from the power strips you buy at the store—those only protect what’s plugged into them, and they don’t stop surges that come through hardwired appliances like your HVAC system, refrigerator, or water heater.
The cost is a few hundred dollars, and it protects tens of thousands of dollars worth of equipment. After a major storm, we get calls from homeowners who lost their TV, their computer, their garage door opener, and half their kitchen appliances because a surge came through the line. Whole-house protection prevents that. It’s one of those upgrades that pays for itself the first time it saves your equipment.
Plan on about two to three days for a complete standby generator installation. Day one is usually site prep and setting the generator pad. We pour a concrete pad or install a composite base, run the gas line (if you’re using natural gas), and trench the electrical line from the generator to your panel.
Day two is the generator installation and electrical hookup. We set the unit, connect it to your panel through a transfer switch, and wire everything according to code. We also program the generator to match your home’s electrical load and test the automatic transfer function to make sure it kicks on when the power drops.
Day three is usually inspection and final testing. The city of Grapevine requires permits for generator installations, so we schedule that and make sure everything passes. Once it’s approved, we walk you through how to operate and maintain the unit. Most Generac and Kohler generators require basic maintenance once or twice a year—oil changes, filter replacements, and a test run. We can handle that for you, or you can do it yourself. Either way, you’ll have backup power whenever the grid goes down.
Stop using that outlet immediately and call an electrician. Warm outlets mean there’s resistance in the connection, which creates heat. That heat can melt wiring insulation, start an electrical fire, or damage whatever’s plugged into the outlet. Sparking is even worse—it means there’s arcing inside the outlet, which is a serious fire hazard.
The most common causes are loose wiring, backstabbed connections (where the wire is pushed into the back of the outlet instead of screwed to the terminal), or an outlet that’s overloaded. Older homes in Grapevine often have aluminum wiring, which expands and contracts with temperature changes and loosens connections over time. That creates heat and increases fire risk.
We can diagnose the problem during a service call, replace the outlet if needed, and check the rest of your home’s outlets to make sure you don’t have the same issue elsewhere. If the problem is in your panel or your wiring, we’ll let you know what needs to happen. Don’t ignore warm or sparking outlets—they don’t fix themselves, and they get worse over time.
It depends entirely on what you need done. A simple outlet replacement or breaker swap might run a couple hundred dollars. A full panel upgrade typically costs between $2,500 and $5,000 depending on the size of the panel and how much rewiring is involved. Whole-house surge protection usually adds another $400 to $800.
Backup generator installations range from $8,000 to $15,000 depending on the size of the unit and whether you’re using natural gas or propane. EV charger installations run $800 to $2,000 depending on how far the run is from your panel to your garage. Rewiring an older home can cost $8,000 to $20,000 depending on square footage and how much of the wiring needs to be replaced.
We give you an upfront price before any work starts, so there’s no guessing. If we find something during the job that changes the scope, we stop and talk to you before moving forward. You’ll know exactly what you’re paying and what you’re getting for it. We don’t do time-and-materials billing or surprise charges—just honest pricing for quality electrical work.
